| Function |
DISPLAY |
Function Description |
| 1 |
LOADING ADJST |
Set TOP margin |
| 2 |
PAPER WIDTH |
Set Paper Width (for print head positioning) |
| 3 |
LINE WIDTH |
Set Maximum Line length (for printing purposes) |
| 4 |
PRINT DIR |
Set BI, UNI, or PRE directional printing |
| 5 |
LF PITCH |
Set CODE6 or CODE8 (changeable by software) or 8 or 9 lpi |
| 6 |
OVERRIDE PRINT |
Override default 17mm Bottom Margin |
| 7 |
AUTO SCROLL |
Autoscroll advances paper to TearOff position after 1 sec |
| 8 |
LABEL MODE |
Designed to prevent labels peeling & causing printer jams |
| 9 |
DEFAULT PG LNG |
Select 11 or 12in, Only valid if Page Length is set to CODE in basic |
| 10 |
P.OUT DETECT |
Set Paper detection ON or OFF |
| 11 |
P.OUT BUZZER |
Set to SOUND or NO-SOUND |
| 12 |
NATIONAL FONT |
Set to one of 14 National fonts |
| 13 |
ZERO STYLE |
Set to Slashed or No-Slash |
| 14 |
1-INCH SKIP |
This leaves 1in of unprinted lines at bottom of page |
| 15 |
EMULATION |
Set Print Driver Emulation |
| 16 |
CHRACTER SET |
Character set availability dependant upon Emulation chosen |
| 17 |
CR SETTING |
Set how the printer is to react to a Carriage Return command |
| 18 |
LF SETTING |
Set how the printer is to react to a Line Feed command |
| 19 |
VT SETTING |
BP mode only- Set how printer reacts to a Vertical Tab command |
| 20 |
20CPI SETTING |
IBM Emulation only-Print at 20cpi or at 12cpi as per older printers |
| 21 |
DWNLD CHR.SET |
Choose between Country or Multilingual character sets |
| 22 |
DWNLD ITALIC |
Disable or enable the IBM italic download command |
| 23 |
ITALIC MODE |
Choose between CODE (software selection) or ALWAYS |
| 24 |
BOLD MODE |
Choose between CODE (software selection) or ALWAYS |
| 25 |
BARCODE CMND |
Should the printer accept the Car Code command |
| 26 |
BARCODE TYPE |
Choose from 13 Bar Code types + Element |
| 27 |
BC HEIGHT |
Set default Bar Code Height (not Postnet) |
| 28 |
NB WIDTH |
Set default Narrow Bar width (not Postnet) |
| 29 |
WB WIDTH |
Set default Wide Bar width (not Postnet) |
| 30 |
NS WIDTH |
Set default Narrow Space width (not Postnet) |
| 31 |
WS WIDTH |
Set default Wide Space width (not Postnet) |
| 32 |
ICG WIDTH |
Set default Intercharacter gap width (where allowed by BC) |
| 33 |
HRI PRINT |
Set Human Readable Interpretation options (None,Above,Below) |
| 34 |
HRI FONT |
Set HRI font (Current, OCR-A, OCR-B) |
| 35 |
CHECK DIGIT |
Add an automatic Check Digit (Not Codabar) |
| 36 |
INTERFACE |
Set Parallel or Serial |
| 37 |
PARITY BIT |
Set parity bit (Serial Interface only) |
| 38 |
DATA LENGTH |
Set Data Length (Serial Interface only) |
| 39 |
STOP BIT |
Set Stop bit (Serial Interface only) |
| 40 |
PROTOCOL |
Set Communication protocol (Serial Interface only) |
| 41 |
BAUD RATE |
Set Data transmission speed (Serial Interface only) |
| 42 |
SERIAL ERROR |
Set how printer reacts to a serial DT error (Serial Interface only) |
| 43 |
BUFFER SIZE |
Set Buffer size |
| 45 |
CSF OPTION |
Is the optional Cut Sheet Feeder fitted |
| 46 |
FACTORY SET |
Resets Printer back to default Factory settings |
| 47 |
SAVE SETUP |
Saves current settings into one of three memory areas |
| 48 |
SOFTWARE SET |
Enables or disables alteration of setup by special software commands |